Product Information

ALS R Type Specifications

ALS R Types (key/set screw type)

[Specifications]

ModelTorqueMisalignmentMax. rotation speed [min-1Static torsional stiffness [N・m/rad]Radial stiffness [N/mm]Moment of inertia [kg・m2Mass [kg]
Nominal [N・m]Max. [N・m]Parallel [mm]Angular [°]Axial [mm]
ALS-014-R240.1010 to +0.634100213801.91×10-70.007
ALS-020-R5100.1010 to +0.823800434001.08×10-60.018
ALS-030-R12.5250.1010 to +1.0159001366506.25×10-60.047
ALS-040-R17340.1010 to +1.211900155017003.87×10-50.15
ALS-055-R601200.1010 to +1.48700200013501.66×10-40.35
ALS-065-R1603200.1010 to +1.57400310014003.57×10-40.51
ALS-080-R3256500.1010 to +1.86000600017101.06×10-31.01
ALS-095-R4509000.101-0.5 to +2.050001000042002.24×10-31.50
ALS-105-R52510500.151-0.9 to +2.045001200050003.72×10-32.05

*Axial displacement of the ALS-014-R to ALS-080-R is not allowed in the negative direction.

*Max. rotation speed does not take into account dynamic balance.

*Stiffness values given are from measurements taken at 20℃.

*The moment of inertia and mass are measured for the maximum bore diameter.

[Dimensions]

Unit [mm]
Modeld1, d2DLL1, L2ESC
Pilot boreMin.Max.
ALS-014-R336.514227813.5
ALS-020-R449.62030101015
ALS-030-R5614303511131.55.5
ALS-040-R582240662516212.5
ALS-055-R5102855783018215
ALS-065-R51438659035202.517.5
ALS-080-R101945801144524322.5
ALS-095-R81955951265026325
ALS-105-R10196010514056283.528

*"Pilot bore" refers to center processing.

[Standard bore diameter]

Unit [mm]
ModelStandard bore diameter d1, d2 [mm]
34566.35899.52510111214151618192024252830323538404245505560
ALS-014-R
ALS-020-R
ALS-030-R
ALS-040-R
ALS-055-R
ALS-065-R
ALS-080-R
ALS-095-R
ALS-105-R

*The bore diameters marked with ● are supported as standard bore diameter.

*ø11 and below have no keyway; ø12 and above can be processed for old JIS standards, new JIS standards, and new standard motors.

*The only standard processing of bore diameters of the ALS-095 and ALS-105 are for new JIS standards and new standard motors.

ALS R Types (clamp types)

[Specifications]

Unit [mm]
ModelMisalignmentMax. rotation speed [min-1Static torsional stiffness [N・m/rad]Radial stiffness [N/mm]Moment of inertia [kg・m2Mass [kg]
Parallel [mm]Angular [°]Axial [mm]
ALS-014-R0.110 to +0.610000213801.98×10-70.007
ALS-020-R0.110 to +0.810000434001.09×10-60.019
ALS-030-R0.110 to +1.0100001366506.19×10-60.045
ALS-040-R0.110 to +1.210000155017004.01×10-50.16
ALS-055-R0.110 to +1.47000200013501.63×10-40.34
ALS-065-R0.110 to +1.55900310014003.69×10-40.54
ALS-080-R0.110 to +1.84800600017101.04×10-31.00

*Axial displacement is not allowed in the negative direction.

*Max. rotation speed does not take into account dynamic balance.

*Stiffness values given are from measurements taken at 20℃.

*The moment of inertia and mass are measured for the maximum bore diameter.

[Dimensions]

Unit [mm]
Modeld1, d2DDBLL1, L2ESBGMTightening torque [N・m]
Min.Max.
ALS-014-R361416.1227813.54.81-M20.4
ALS-020-R482020301010156.51-M2.51
ALS-030-R61430303511131.55.510.51-M31.5
ALS-040-R8204043.2662516212.5151-M57
ALS-055-R10285555783018210.5201-M614
ALS-065-R14356569.89035202.511.524.51-M830
ALS-080-R194580801144524311.5301-M830

*The øDB value is measured assuming that the head of the clamping bolt is larger than the external diameter of the hub.

*The nominal diameter for the clamping bolt M is equal to the quantity minus the nominal diameter of the screw threads, where the quantity is for a hub on one side.

Standard bore diameter and allowable transmission torque

ModelStandard bore diameters d1, d2 [mm] and rated transmission torque [N・m]
34566.357810111214151618192022242528303542
ALS-014-R0.310.420.540.65
ALS-020-R1.21.62.12.22.63.0
ALS-030-R2.02.23.44.75.46.07.4
ALS-040-R8162331343434
ALS-055-R384148515461677180
ALS-065-R616875798996114
ALS-080-R108121151194

*Bore diameters whose fields contain numbers are supported as the standard bore diameters.

*Bore diameters whose fields contain numbers are restricted in their rated transmission torque by the holding power of the shaft connection component. The numbers indicate the rated transmission torque value [N·m].

*The recommended processing tolerance for paired mounting shafts is the h7 class. However, for a shaft diameter of ø35, the tolerance is -0.025 to +0.010.

*Bore diameters between the minimum and maximums shown in the dimensions table are compatible, but bore diameters other than those shown in the above table require other arrangements. Contact Miki Pulley for details.

[Element]

Unit [mm]
ModelFR1R2KA
ALS-014-R-EL6.23.5--2.51.2
ALS-020-R-EL8.26.2--3.41.4
ALS-030-R-EL10.28.5--42.2
ALS-040-R-EL1218--4.53
ALS-055-R-EL1424--5.53
ALS-065-R-EL1530--5.54
ALS-080-R-EL18371574
ALS-095-R-EL20432084
ALS-105-R-EL2150208.54

[Standard Hole-drilling Standards]

Unit [mm]
Models compliant with the old JIS standards (Class 2)Models compliant with the new JIS standardsModels compliant with the new motor standards
Nominal bore diameterBore diameter (d1, d2)Keyway width (W1, W2)Keyway height (T1, T2)Set screw hole (M)Nominal bore diameterBore diameter (d1, d2)Keyway width (W1, W2)Keyway height (T1, T2)Set screw hole (M)Nominal bore diameterBore diameter (d1, d2)Keyway width (W1, W2)Keyway height (T1, T2)Set screw hole (M)
ToleranceH7, H8E9+0.30-ToleranceH7H9+0.30-ToleranceG7, F7H9+0.30-
33+0.0180--1-M3--------------------
44+0.0180--2-M3--------------------
55+0.0180--2-M3--------------------
66+0.0180--2-M4--------------------
6.356.35+0.0220--2-M4--------------------
77+0.0220--2-M4--------------------
88+0.0220--2-M4--------------------
99+0.0220--2-M4--------------------
9.5259.525+0.0220--2-M4--------------------
1010+0.0220--2-M4--------------------
1111+0.0180--2-M4--------------------
1212+0.01804+0.050+0.02013.52-M412H12+0.01804+0.030013.82-M4----------
1414+0.01805+0.050+0.02016.02-M414H14+0.01805+0.030016.32-M414N14+0.024+0.0065+0.030016.32-M4
1515+0.01805+0.050+0.02017.02-M415H15+0.01805+0.030017.32-M4----------
1616+0.01805+0.050+0.02018.02-M416H16+0.01805+0.030018.32-M4----------
1717+0.01805+0.050+0.02019.02-M417H17+0.01805+0.030019.32-M4----------
1818+0.01805+0.050+0.02020.02-M418H18+0.01806+0.030020.82-M5----------
1919+0.02105+0.050+0.02021.02-M419H19+0.02106+0.030021.82-M519N19+0.028+0.0076+0.030021.82-M5
2020+0.02105+0.050+0.02022.02-M420H20+0.02106+0.030022.82-M5----------
2222+0.02107+0.061+0.02525.02-M622H22+0.02106+0.030024.82-M5----------
2424+0.02107+0.061+0.02527.02-M624H24+0.02108+0.036027.32-M624N24+0.028+0.0078+0.036027.32-M6
2525+0.02107+0.061+0.02528.02-M625H25+0.02108+0.036028.32-M6----------
2828+0.02107+0.061+0.02531.02-M628H28+0.02108+0.036031.32-M628N28+0.028+0.0078+0.036031.32-M6
3030+0.02107+0.061+0.02533.02-M630H30+0.02108+0.036033.32-M6----------
3232+0.025010+0.061+0.02535.52-M832H32+0.025010+0.036035.32-M8----------
3535+0.025010+0.061+0.02538.52-M835H35+0.025010+0.036038.32-M8----------
3838+0.025010+0.061+0.02541.52-M838H38+0.025010+0.036041.32-M838N38+0.050+0.02510+0.036041.32-M8
4040+0.025010+0.061+0.02543.52-M840H40+0.025012+0.043043.32-M8----------
4242+0.025012+0.075+0.03245.52-M842H42+0.025012+0.043045.32-M842N42+0.050+0.02512+0.043045.32-M8
4545+0.025012+0.075+0.03248.52-M845H45+0.025014+0.043048.82-M10----------
4848+0.025012+0.075+0.03251.52-M848H48+0.025014+0.043051.82-M1048N48+0.050+0.02514+0.043051.82-M10
5050+0.025012+0.075+0.03253.52-M850H50+0.025014+0.043053.82-M10----------
5555+0.030015+0.075+0.03260.02-M1055H55+0.030016+0.043059.32-M1055N55+0.060+0.03016+0.043059.32-M10
5656+0.030015+0.075+0.03261.02-M1056H56+0.030016+0.043060.32-M10----------
6060+0.030015+0.075+0.03265.02-M1060H60+0.030018+0.043064.42-M1060N60+0.060+0.03018+0.043064.42-M10

*Tolerance will be h8 class for hole diameter equal to or less than ø10 mm.

*The set screw size is M3 for ALS-014.

[Distance from set screw edge]

ModelALS-014ALS-020ALS-030ALS-040ALS-055ALS-065ALS-080ALS-095ALS-105
Distance from set screw edge C [mm]3.555.512.51517.522.52528

Related Product