Product Information

121(10G) Types (Double clutches)


121(10G) Types (Double clutches) Specifications

121 (10G) Types


ModelSizeDynamic friction torque Td [N・m]Static friction torque Ts [N・m]Coil (at 20℃)Heat resistance classMax. rotation speed [min-1Rotating part moment of inertia J [kg・m2Total work performed until readjustment of the air gap ET [J]Armature pull-in time ta [s]Torque build-up time tp [s]Torque decaying time td [s]Mass [kg]
Voltage [V]Wattage [W]Current [A]Resistance [Ω]For hub inputFor shaft input
121-06-10G0655.5DC24110.4652B30001.55×10-41.05×10-436×106C: 0.020/B: 0.015C: 0.041/B: 0.033C: 0.020/B: 0.0151.7
121-08-10G081011DC24150.6338B30004.75×10-43.00×10-460×106C: 0.023/B: 0.016C: 0.051/B: 0.042C: 0.030/B: 0.0253.1
121-10-10G102022DC24200.8329B30001.44×10-39.45×10-4130×106C: 0.025/B: 0.018C: 0.063/B: 0.056C: 0.050/B: 0.0306.5
121-12-10G124045DC24251.0423B30004.50×10-32.75×10-3250×106C: 0.040/B: 0.027C: 0.115/B: 0.090C: 0.065/B: 0.05010.5
121-16-10G168090DC24351.4616B30001.34×10-29.05×10-3470×106C: 0.050/B: 0.035C: 0.160/B: 0.127C: 0.085/B: 0.05521
121-20-10G20160175DC24451.8813B25004.18×10-22.65×10-210×108C: 0.090/B: 0.065C: 0.250/B: 0.200C: 0.130/B: 0.07038.5
121-25-10G25320350DC24602.509.6B20009.80×10-27.45×10-220×108C: 0.115/B: 0.085C: 0.335/B: 0.275C: 0.210/B: 0.12570

*The dynamic friction torque, Td, is measured at a relative speed of 100 min-1. Depending on the initial torque characteristics, break-in to condition the engaging surfaces may also be required.

*The rotating part moment of inertia for shaft input is the value with one armature type-5.


SizeDimensions of part
SizeShaft dimensions
Q1 Q2 S1 S2 U1 U2 V1 V2 X1 X2 W1, 2
062520113812.539.5M4×0.7, length: 83-M4×0.7, length: 43° to 120°60°4
08302514451647M4×0.7, length: 83-M4×0.7, length: 63° to 120°60°5
10403019552157M6×1, length: 114-M4×0.7, length: 84° to 90°45°5
12504024642767M6×1, length: 114-M4×0.7, length: 84° to 90°45°7
16605028753178M6×1, length: 116-M5×0.8, length: 86° to 60°30°7
208060389041.593.5M10×1.5, length: 174-M6×1, length: 124° to 90°45°10
25110704211545.5118.5M10×1.5, length: 178-M6×1, length: 128° to 45°22.5°12

*The input/output keyways are old JIS standard class 2 while the key is old JIS standard class 1. Note that the keyway dimensions of the unit hub part do not conform to the old JIS standard. Check them on the dimensions table above.

*When inserting pulleys or the like onto input/output shafts, use the supplied insertion set.

*The 121-25-10G base is a casting.

Related Product